INSTRUCTION MANUAL WARRANTY CERTIFICATEALUMA WETBY
4 Step 1. (Fig. 5) Remove the metal plate and upper cover by remove the screws from the motor.Step 2. (Fig. 6) Insert the blade through the acce
5WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the proper insta
OUTLET BOXHANGER BRACKETDOWNRODSUPPLYWIRESFig. 8Fig. 10 Fig. 11Fig. 9 Fig. 13REGISTRATIONSLOTCROSS PINHANGERBALLDOWNRODHITCHPINLOCKPINSET SCREWSSET S
6ELECTRICAL CONNECTIONSWARNING:: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring. N
Fig. 14Fig. 15RECEIVERHANGER BRACKETStep 3. Receiver to House Supply Wires Electrical Connections: Connect the WHITE wire (Neutral) from the outlet bo
Fig. 16WHITE (NEUTRAL)WHITE (NEUTRAL)GREEN OR BARECOPPER (GROUND)WHITE ("AC IN N")WHITE ("TO MOTOR N")GROUND-(GREEN)(CONNECT TOGR
7FINISHING THE INSTALLATION Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw
Fig. 18INSTALLING THE LIGHT KIT MOUNTING PLATEStep 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove)Step 2
9Fig 19INSTALLING THE LIGHT PLATE NOTE: Before starting installation, make sure power is turned off at the circuit breaker.1. Remove 1 of 3
10WARNING: Shut of the power supply before removing or replacing lamp. In handling of halogen bulb, care should be taken not to touch it with your bar
Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
Fig 20 Fig 21MOUNTING PLATEBULBGLASS SHADEMOUNTING PLATEALUMINUM COVER
11OPERATING THE REMOTE CONTROL/WALL CONTROLRestore Power to Ceiling Fan.A. Buttons: These buttons are used to set the fan speeds as fo
Fig 22Fig 23Speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of fans.NOTE: Wait for the fan to
12Here are some suggestions to help maintain your fan.1. Because of the fan's natural movement some connections may become loose. Check the suppo
13TROUBLESHOOTING SYMPTOM Fan will not startCheck to make sure the wall switch is turned on.Check circuit fuses or breakers.Caution! Make sure t
SYMPTOM Fan WobbleNOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even though blades
SYMPTOM Frequency InterferenceTurn the power off to your ceiling fan.Please use a small size tool to change the frequency settings on the control sys
SPECIFICATIONSThese are typical readings. Your actual fan may vary. They do not include amps and wattage used by the light(s).For any additional infor
The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only vali
Date Purchased Store Purchased Model Number S
CONTENTSSAFETY RULES... PACKAGE CONTENTS...
SAFETY RULES1 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all inst
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.
215. Balancing kit16. 100w Mini-Can halogen bulbA. Mounting hardware: #10 x 1.5 Wood screws (2 PCs.) #8 x 3/4" Machine screws (2P
3Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. INSTALLING THE FANMOUNTING OPTIONSIf there i
Kommentare zu diesen Handbüchern