MinkaAire GYRO WET Bedienerhandbuch

INSTRUCTION MANUAL WARRANTY CERTIFICATEPatents PendingINSTRUCTION MANUAL WARRANTY CERTIFICATEGYRO WETBYTMU.S. Patents: D478,975; D489,443; D489,809

4 WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the prop

Fig. 5Fig. 7 Fig. 8Fig. 6Fig. 10Fig. 9CANOPY COVEROUTLET BOXHANGER BRACKETDOWNRODSUPPLYWIRESREGISTRATIONSLOTCROSS PINHANGERBALLDOWNRODHITCHPINLOCKPINS

5 WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring. NOTE: The Aire Con

Step 3. Receiver to House Supply Wires Electrical Connections: Connect the WHITE wire (Neutral) from the outlet box to the WHITE wire marked "AC

Fig. 13Fig. 14WALLCONTROLBLACKBLACKBLACKBLACKBLACKWHITEBLUEBLUEGROUNDGROUNDGRAYGREENINPUTAC120VAC SUPPLYWHITE (NEUTRAL)WHITE (NEUTRAL)GREEN OR BARECOP

6Fig. 15INSTALLING THE WALL TRANSMITTER WARNING! HOOK UP "IN SERIES" ONLY. DO NOT CONNECT NEUTRAL SUPPLY WIRE OF ELECTRIC CIRCUIT TO THE TRA

7Step 1. Slide the canopy up to ceiling and over the two screws on hanger bracket. Rotate canopy clockwise, next, while holding the canopy with

8WARNING: Shut of the power supply before removing or replacing lamp. In handling of halogen bulb, care should be taken not to touch it with your bare

Fig. 17Fig. 18METAL LIGHT CAPTo install the metal light cap follow Step 2. above. To remove the metal light cap, you must first press and then turn co

Fig. 19Step 1. Pull the "PULL" knob out to unlock the fan, tilt the fan body to desired location, push back the "PULL" knob to loc

This product is protected by United States Federal and/or State Law, including Patent, Trademark and/or Copyright laws.Manual design and all elements

10OPERATING THE REMOTE CONTROL/WALL TRANSMITTERRestore Power to Ceiling Fan.A. Buttons: These buttons are used to set the fan speeds a

11Here are some suggestions to help maintain your fan.1. Because of the fan's natural movement some connections may become loose. Check the suppo

12TROUBLESHOOTINGSYMPTOM Fan will not start Check to make sure the wall switch is turned on.Check circuit fuses or breakers.Caution! Make sure the

SYMPTOM Fan WobbleNOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even though blades

SYMPTOM Frequency InterferenceTurn the power off to your ceiling fan.Please use a small size tool to change the frequency settings on the control sys

RPMCFMN.W. G.W. C.F.14"120120120Fan Size Speed Volts Amps WattsLow MediumHigh13.65kgs18.11 kgs6.58'0.70 0.80 0.8548 67 102720 980 13502900 3

Minka-Aire warrants to the original owner that this fan will be free from defects in material an

Date Purchased Store Purchased Model Number S

CONTENTSINSTALLING THE LIGHT BULB AND GLASS SHADE...ADJUSTING THE TILT ANGLE...

SAFETY RULES1 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all inst

WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING SYSTEM MARKED ACC

21. Fan motor assembly2. Hanger bracket 3. Canopy4. Canopy cover5a. Standard downrod assembly 5b. Minimum-length downrod (for close to

3Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. INSTALLING THE FANMOUNTING OPTIONSIf there